Showing posts with label Bird House Crafts. Show all posts
Showing posts with label Bird House Crafts. Show all posts

Saturday, October 15, 2011

glue together a birch bark birdfeeder

My birch bark bird feeder
Brief Description: This bird feeder is easy to make because you start with a prefabricated wooden bird feeder. I made it many years ago while camping at Arcadia. I collected the bark from a peeling birch tree in the woods and glued it to the bird feeder.

Supply List:
 * prefabricated wooden bird feeder
 * wood glue
 * small stones, about 30
 * large rubber bands or twine
 * hot glue and hot glue gun

Directions:
   1. Make sure the surface of the wooden bird feeder is clean before your begin.
   2. Glue strips of birch bark to every surface area of the feeder excluding the "floor" of the feeder.
   3. You may need to wrap twin or rubber bands around the exterior of the feeder to help keep the bark from sliding off while the wood glue dries.
   4. After the bark is dry, hot glue the stones onto the floor of the bird feeder with a hot glue gun.



thefrugalcrafter makes a birch bark frame

More craft projects made from birch bark:

Wednesday, September 28, 2011

craft project: mosaic bird house

I purchased this prefabricated, 
wooden birdhouse from a craft store
 called Michael's. It is an actual
 birdhouse that may be used 
outdoors.
Brief Description: This mosaic birdhouse can be hung outside if you would prefer. My mother keeps it inside in her sunroom.

Supply List:
   1. Selection of mosaic tiles, glass marbles, tiny mirrors, seashells
   2. Cement grout
   3. Elmer’s wood glue
   4. Plastic-like gloves
   5. Old damp rags or paper towels
   6. Prefabricated wooden bird house
   7. white acrylic paint
   8. burnt umber acrylic paint  
   9. bucket of clean water

Directions:
  1.  Glue the tiles directly to the surface of the prefabricated wooden bird house.
  2.  Let the applied tiles dry over night to ensure that the glue has hardened. Do not check to see if the glued tiles have stuck to the surface permanently. Some of them will, some of them may only seem temporarily attached. The application of this step is necessary to help the tiles to stay in place before grouting them only.
  3. Mix the grout solution according to the directions on the label.
  4. Wear gloves if the label says that it is necessary.
  5. Gingerly apply the grout directly onto the surface of the tile work. Make sure that the grout does get pushed into as many of the cracks as possible. This is a bit messy.
  6. Wash your gloves thoroughly and you may put them back on or choose to remove them all together at this point. Be cautious about this removal however, some people do have mild skin allergies to grout and will develop a rash when coming in direct contact with it when its wet.
  7. Now your going to delicately wipe down the surface of your tiles with a damp rag or paper towel. You will be throwing these towels away. If you wish to rinse and squeeze out a sponge or towels as you work, keep an old bucket full of water for this procedure. Do not wash this contaminated water down a sink! Grout will collect in pipes and harden. You will need to pour this old water down a sewer pipe outside or simply find an area of your yard where you may dispose of it. Grout won't hurt an old leaf pile or the ground where plants are not growing.
  8. You want your project to look clean on the surface of the tiles when you are finished. The cracks between the tiles should also be completely filled with grout.
  9. Leave your mosaic project out over night to harden properly.
  10. If you see remaining grout on the surface of your tiles after it has hardened, you may go over the surface of these tiles with a light weight sand paper and damp sponge again.
Additional Suggestions: You may wish to seal the exposed wooden areas with a tough varnish if you choose to hang your bird house outdoors.

All instructions and photographs, templates are copyrighted by Grimm 2011